Cree 5 Watt XPG3 LED for RYOBI 18V FL1800 Cordless Light - Brilliant 320 Lumen

Description

Cree 5 Watt XPG3 LED for RYOBI 18V FL1800 Cordless Light - Brilliant 320 Lumen
RYOBI 18V Replacement 5-W Cree XPG2 LED Bulb / FL1800 Cordless Light
RYOBI 18 VOLT Flashlight Replacement 5-W Cree LED Bulb / FL1800 Cordless light
Note:
NOT FOR Ryobi P704 - We have a Cree 5 Watt XPG3 LED made for the *** P704 *** . Please See
https://www.ebay.com/itm/333595351196
NOTE:
This LED IS NOT for Sears Craftsman
C3 19.2 V Work Lights. Please See
https://www.ebay.com/itm/333374625387
------ NEW Cree XPG3 UPGRADED FROM our previous Cree XPG2 ******
Cree® XLamp® XP-G3 LED Delivers More Lumens-Per-Watt
Use this
320 LUMEN
LED PR Bulb to upgrade standard P13.5S bulb lights
for superior brightness, efficiency, and longevity.
LED UPGRADE For the Following
Rechargeable Work lights and Replacement Bulbs:
Work Light Upgrade For:
Bulbs Upgrade For:
Ryobi
FL1800
18v
Ryobi
780287001
19.2v
Ryobi  is a trademark of Ryobi Limited
--- Super Bright Led's for Less ---
Simply replace your existing bulb with this LED – no modifications necessary!
*Please note, LED bulb will be bright but not as bright as highest power Krypton or Xenon XPR18 bulb over 10 watts with battery fully charged.
But incandescent light output decreases @ 70% at discharged battery down to @179 lumens rated.
These regulated LEDs provide steady light over the full greatly extended run time. Also with the LED bulb long life it may never need replacing.
Universal Voltage Works with standard flashlights and Work Lights 6.5 Volt to 30 Volts
Standard DC
Polarity (+) on bottom contact or Flange !
Minimizes battery and bulb replacement waste
Focusability of flashlight is preserved with these point source LEDs
Brighter Light for improved vision for
enhanced visibility of fine detail
Longer battery life from high efficiency LED
Long lamp life 50,000 hours of continuous use
Dependable and shock resistant
Easy To Install
Features:
INTENSE BRIGHT LIGHT
output comes from the ultra-efficient LED. The LED does not fade when it gets hot, so its light output is stable even after extended run times.
FOCUSABILITY
These LED Point source lights preserve one of the most outstanding features of many flashlights, the ability to focus. A focused beam that throws a bright beam a very long distance.
MAXIMUM EFFICIENCY
These
LEDs are powered below their maximum rating for longer life and higher lumens per watt of battery power.
LONGER BATTERY LIFE
results from the higher efficiency of the LED compared to the standard incandescent bulb 10 Lumens / watt. These LED maintain a brighter white light output as the batteries discharge than incandescent bulbs which turn to an amber light.
INDESTRUCTIBLE LED
performance and lifetime operation. Unlike incandescent bulbs with a fragile filament that breaks, LEDs wear out very slowly. This is likely to be the last bulb you will ever need to buy. The rated lifetime is 50,000 hours.
EASY TO INSTALL
as if just replaces your existing bulbs - no modifications necessary
See the difference !
Standard PR Incandescent vs. LED
1) Warning! - Do not look directly into lit LED Lamps at a close distance or shine into eyes, as they are extremely bright and could cause eye damage.
2) Warning! - For safety always follow manufactures safety and operational instructions.
3) Caution! - Remove batteries, turn-off or disconnect power before changing bulb.
* The perfect bulb (High Brightness and Longer Battery life run time).
This Cree is a Point
source
LED (Better were focused light is desired) and the Epistar in other add below is a diffused LED (Wide angle area Light is desired).
See my other add for more details.
https://www.ebay.com/itm/Epistar-Cree-LED-Flashlight-Bulb-Upgrade-Universal-5V-30VOLT-4-Cell-N-Up-Work-/231314842982?ssPageName=STRK:MESE:IT#ht_3349wt_789
Description:
Upgrade / Replacement for standard Work Light applications that take a flange base light bulb for 6.5-30
Volt battery operated products (Zink, Alkaline,  lithium, NiCad).
*EPISTAR is a trademark of EPISTAR Corporation
*CREE is a trademark of Cree, Inc.
* Draco Products is not affiliated with Epistar Corporation or Cree, Inc.
☛
·
Buy two now and save with discounted shipping,
why not get two?
This is a very popular style of bulb for Many Work Lights, and flash lights
*Specifications are accurate for this Miniature LED Bulb.
Applications for this standard Flange type bulb are too numerous to list so purchaser is responsible for compatibility with their actual product.
The Lamp has a STANDARD 'PR' Base - P13.5s is International standard flanged base
, 9.2mm Diameter, with flange "V" notch
★
Thank You.
Please return a positive review for good service, Thank You.
© 2015-2020 Draco Products. All Rights Reserved
Draco Products
provides
quality technology products
supporting our 1000's of satisfied customers
.
For example:
- Great light replacement
I bought this for a Ryobi flashlight that has a regular filament light bulb. The LED fits the same light holder, and they included a spacer that made the LED set in the same place as the filament. It now gives off a perfect round bight beam using very little power.
- LIGHT BULB
A great light bulb. Shock resistant. Lasts for ever! Maybe the last bulb I'll ever buy????
- Thanks!! Fast shipping. Item as described!!
- You got to try these. really bright
- Excellent Seller, highly Recommended
- Received item as described by seller in ad. Fast shipper. Great service.
- Fast ship and received exactly what I wanted
"
Draco Products provides exemplary
customer service
and
money-back satisfaction guarantee"